燃氣發電機組在運行過程中可能會遇到多種常見故障，這些故障涉及多個系統和部件。以下是一些常見的故障及其處理方案：

　　Gas turbine generators may encounter various common faults during operation, which involve multiple systems and components. Here are some common faults and their solutions:

　　一、缸套水溫度高

　　1、 High cylinder liner water temperature

　　現象：缸套水溫度異常升高。

　　Phenomenon: Abnormal increase in cylinder liner water temperature.

　　原因：

　　Reason:

　　漏水或運行損耗使缸套水缺失。

　　Leakage or operational losses result in a lack of water in the cylinder liner.

　　散熱水箱日久積塵或風扇電機壞使散熱效果不佳。

　　The long-term accumulation of dust in the radiator or the failure of the fan motor result in poor heat dissipation effect.

　　節溫器故障未打開。

　　Thermostat malfunction did not open.

　　缸套水溫度傳感器或電路故障。

　　Cylinder liner water temperature sensor or circuit malfunction.

　　處理方案：

　　Solution:

　　檢查散熱水箱電機運行是否正常。

　　Check if the cooling water tank motor is running normally.

　　清理散熱水箱積塵，更換故障的風扇電機。

　　Clean the dust accumulation in the radiator and replace the faulty fan motor.

　　更換故障的節溫器。

　　Replace the faulty thermostat.

　　檢查缸套水溫度傳感器外觀及其電路回路，修復或更換故障部件。

　　Check the appearance and circuit of the cylinder liner water temperature sensor, repair or replace faulty components.

　　二、缸套水溫度低

　　2、 Low cylinder liner water temperature

　　現象：缸套水溫度低于正常范圍。

　　Phenomenon: The cylinder liner water temperature is below the normal range.

　　原因：

　　Reason:

　　加熱器故障不加熱。

　　The heater is malfunctioning and not heating up.

　　缸套水溫度傳感器或電路故障。

　　Cylinder liner water temperature sensor or circuit malfunction.

　　節溫器故障未關閉。

　　Thermostat malfunction not closed.

　　處理方案：

　　Solution:

　　檢查加熱器、溫控開關以及停機繼電器是否異常，更換故障部件。

　　Check if the heater, temperature control switch, and shutdown relay are abnormal, and replace the faulty components.

　　檢查傳感器及電氣回路是否有故障并排除。

　　Check whether there are any faults in the sensors and electrical circuits and eliminate them.

　　三、水泵漏水

　　3、 Water pump leakage

　　現象：水泵出現漏水現象。

　　Phenomenon: The water pump is leaking.

　　原因：

　　Reason:

　　水泵長期運行導致溢水塞老化。

　　Long term operation of the water pump leads to aging of the overflow plug.

　　油液污物淤塞導致堵孔。

　　The blockage of oil and dirt leads to blockage of the hole.

　　處理方案：

　　Solution:

　　取出溢水塞進行檢查和更換。

　　Remove the overflow plug for inspection and replacement.

　　清理油液污物，防止堵孔。

　　Clean the oil and dirt to prevent blockage of the hole.

　　四、設備無法啟動

　　4、 The device cannot start

　　現象：燃氣發電機組無法啟動。

　　Phenomenon: The gas generator set cannot be started.

　　原因：

　　Reason:

　　電池電壓不足。

　　The battery voltage is insufficient.

　　點火系統故障（如點火線圈損壞、火花塞損壞）。

　　Ignition system malfunction (such as damaged ignition coil, damaged spark plug).

　　氣路故障（如氣瓶壓力不足、燃氣管道堵塞）。

　　Gas circuit failure (such as insufficient pressure in gas cylinders, blockage in gas pipelines).

　　發動機內部故障。

　　Internal engine malfunction.

　　處理方案：

　　Solution:

　　檢查電池電壓，確保電池充電完好。

　　Check the battery voltage to ensure that the battery is fully charged.

　　檢查點火系統部件，如點火線圈、火花塞以及點火控制模塊是否正常工作。

　　Check whether the ignition system components, such as ignition coils, spark plugs, and ignition control module, are working properly.

　　檢查氣路及燃料系統，確保燃氣閥門開啟且供應穩定，清理堵塞物。

　　Check the gas circuit and fuel system to ensure that the gas valve is open and the supply is stable, and clean any blockages.

　　檢查發動機內部是否有故障，如氣缸磨損、氣門密封不嚴等，并進行修復。

　　Check whether there are any internal faults in the engine, such as cylinder wear, loose valve sealing, etc., and repair them.

　　五、排氣溫度異常

　　5、 Abnormal exhaust temperature

　　現象：排氣溫度高于正常范圍。

　　Phenomenon: The exhaust temperature is higher than the normal range.

　　原因：

　　Reason:

　　負荷過大。

　　Excessive load.

　　排氣不暢。

　　Poor exhaust.

　　氣缸、氣門等部位沉積物過多。

　　Excessive deposits in cylinders, valves, and other parts.

　　處理方案：

　　Solution:

　　檢查排氣系統是否堵塞，保持正常排氣。

　　Check if the exhaust system is blocked and maintain normal exhaust.

　　適當降低發電機負荷，保持額定值運行。

　　Reduce the load of the generator appropriately and maintain rated operation.

　　清理氣缸、氣門等部位的沉積物。

　　Clean the deposits on the cylinders, valves, and other parts.

　　六、產生爆震

　　6、 Generate detonation

　　現象：燃氣發電機組在運行過程中產生爆震。

　　Phenomenon: Gas generator sets produce detonation during operation.

　　原因：

　　Reason:

　　煤氣溫度過高。

　　The gas temperature is too high.

　　熱值調整不正確。

　　The adjustment of calorific value is incorrect.

　　爆震傳感器及線路故障。

　　Knock sensor and circuit malfunction.

　　燃燒室氣門面、氣門座等部位有焦油、萘渣等雜質堆積。

　　There is accumulation of impurities such as tar and naphthalene residue on the combustion chamber valve face and valve seat.

　　處理方案：

　　Solution:

　　檢查煤氣量與熱值是否匹配，調整熱值使修正系數保持100%運行，最低不得低于95%。

　　Check if the gas volume matches the calorific value, adjust the calorific value to maintain a correction factor of 100% operation, with a minimum of 95%.

　　檢查煤氣溫度是否高于技術要求，通過調整煤氣預熱溫度等措施予以解決。

　　Check if the gas temperature is higher than the technical requirements, and solve the problem by adjusting the gas preheating temperature and other measures.

　　檢查爆震傳感器及線路是否有故障并排除。

　　Check and eliminate any faults in the knock sensor and circuit.

　　清理燃燒室氣門面、氣門座等部位的雜質堆積。

　　Clean up the accumulation of impurities on the combustion chamber valve face, valve seat, and other parts.

　　七、發電機組輸出不穩定或電壓異常

　　7、 The output of the generator set is unstable or the voltage is abnormal

　　現象：發電機組輸出電壓不穩定或異常。

　　Phenomenon: The output voltage of the generator set is unstable or abnormal.

　　原因：

　　Reason:

　　控制系統故障。

　　Control system malfunction.

　　電路連接不良。

　　Poor circuit connection.

　　電源負載過大。

　　The power load is too high.

　　處理方案：

　　Solution:

　　檢查控制系統，確保電壓調節器工作正常。

　　Check the control system to ensure that the voltage regulator is working properly.

　　檢查電路連接，確保接線盒和斷路器正常，電路連接牢固。

　　Check the circuit connections to ensure that the junction box and circuit breaker are functioning properly and the circuit connections are secure.

　　調整電源負載，避免過大負載導致電壓波動或輸出不穩定。

　　Adjust the power load to avoid voltage fluctuations or unstable output caused by excessive load.

　　八、機油溫度過高或機組運行噪音過大

　　8、 High oil temperature or excessive noise during unit operation

　　現象：機油溫度過高或機組運行噪音過大。

　　Phenomenon: The oil temperature is too high or the operating noise of the unit is too loud.

　　原因：

　　Reason:

　　潤滑系統故障。

　　Lubrication system malfunction.

　　散熱系統故障。

　　Cooling system malfunction.

　　阻尼裝置故障。

　　Damping device malfunction.

　　處理方案：

　　Solution:

　　檢查潤滑系統，確保機油質量符合要求，機油位正常，機油泵運轉正常。

　　Check the lubrication system to ensure that the oil quality meets the requirements, the oil level is normal, and the oil pump is running normally.

　　檢查散熱系統，確保冷卻風扇、散熱片等散熱良好。

　　Check the cooling system to ensure good heat dissipation of cooling fans, heat sinks, and other components.

　　檢查阻尼裝置，確保減震效果良好，減少振動和噪音。

　　Check the damping device to ensure good shock absorption effect and reduce vibration and noise.

　　綜上所述，燃氣發電機組的常見故障涉及多個系統和部件。在出現故障時，應根據具體情況采取相應的處理措施以恢復機組性能并防止故障擴大。同時，建議定期進行維護和檢查以確保機組的正常運行。

　　In summary, common faults in gas turbine generators involve multiple systems and components. When a fault occurs, corresponding measures should be taken according to the specific situation to restore the performance of the unit and prevent the fault from expanding. Meanwhile, it is recommended to conduct regular maintenance and inspections to ensure the normal operation of the unit.

　　本文由 燃氣發電機組 友情奉獻.更多有關的知識請點擊   http://www.ptvydps.cn   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from a gas generator set For more related knowledge, please click http://www.ptvydps.cn Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.